Gearmotors

Right angle reduction motor

1. Installation / disassembly components coupled to the motor shaft end, do not hit shaft hard to prevent the other side ofmotor shaft encoder was knocked out bad. 2. Striving to make the best of its shaft to prevent vibration and bearing damage.

Micro speed regulating motor

Induction motor IK and RK series voltage: single-phase (110V-220V) power: (6W-200W) three-phase (220V-380V) power: (25W-200W) Induction motor for single direction operation There are two types of induction motors: single-phase power supply and three-phase power supply, and there are also terminal box types available for selection, commonly used for conveyor belt and other purposes. Reversible motors for forward and reverse direction operation are all single-phase power sources, and there are also terminal box types available for selection. Due to the simple brake pads hidden inside the reversible Mazda, it can instantly change direction and is suitable for frequent changes in operating direction.

Right angle reduction motor

1. When the reducer shaft is used with the mechanical connection of sprocket, conveyor belt and gear, the output shaft allowable O.H.L should be considered. 2. The list of allowable O.H.L value load position in the (solid shaft: the middle of the output shaft; hollow shaft: at 20mm from the end of the shaft) 3.15 than a load inertia can not be greater than 2 times the allowable shaft rotation 4.* Marked for restricted models, please pay special attention to the allowable value in the table of allowable torque.

60B servo motor

1. Installation / disassembly components coupled to the motor shaft end, do not hit shaft hard to prevent the other side ofmotor shaft encoder was knocked out bad. 2. Striving to make the best of its shaft to prevent vibration and bearing damage.

Gear Motor

1. When the reducer shaft is used with the mechanical connection of sprocket, conveyor belt and gear, the output shaft allowable O.H.L should be considered. 2. The list of allowable O.H.L value load position in the (solid shaft: the middle of the output shaft; hollow shaft: at 20mm from the end of the shaft) 3.15 than the load inertia can not be greater than 2 times the allowable shaft rotation

Precision Planetary Reducer

1.Maximum torque confirms that the instantaneous peak load torque and starting torque with load cannot exceed the rated maximum torque of the reducer T. Specific parameter values are listed in the table of reducer ratings. 2. Cantilever load is mainly for cantilevered rack and pinion, timing belt pulley, etc. that need to carry large radial force or axial force. Selection of swing, in accordance with a certain speed and the force point in the shaft extension a 1/2 consider, require Cao inter need radial force or axial force is less than the standard value of the sample (pay attention to the speed of rotation value. The lower the rotational speed, the relative bearing radial force will improve the force paste farther away from the shoulder of the shaft, the bearing radial force will decline). If with special circumstances, you can contact with our engineering staff.

Gear Motor

1. When the reducer shaft is used with the mechanical connection of sprocket, conveyor belt and gear, the output shaft allowable O.H.L should be considered. 2. The list of allowable O.H.L value load position in the (solid shaft: the middle of the output shaft; hollow shaft: at 20mm from the end of the shaft) 3.15 than the load inertia can not be greater than 2 times the allowable shaft rotation

Four series of hardened gears - F series

The mechanical brake can be supplied in one sweet package with the motor and gear motor as required. The brake is an electromagnetic disc brake with a DC ring, which is opened by electromagnetic force and braked by spring force. Its braking principle implies a power-off system. The basic safety needs are met. The brake can be released mechanically if it is fitted with a hand-ventilation release. The hand release is available in the form of a handle or a flat head screw which automatically springs back and a flat head screw which locks in the released position. The brake is controlled by a brake control system installed in the motor connection box or electrical cabinet.

Turbolift

Worm gear screw jack is through the worm gear screw performs moving up , down and forward by worm driv s sis widely used in fields of machinery , architecture , chemistry etc . The lifer has advantages of compact structure , , . 7size , easy installation , good reliability , high stability and long life-span . It has self locking . The maximum loadingcapability is 2.5 to 150 ton and the maximum input RPM is 1500r / m . The environment working temperature isbetween-20c and 100C